Condensation heat transfer of pure steam and steam from gas–steam mixture in tubes of AES-2006 PHRS SG heat exchanger


Citar

Texto integral

Acesso aberto Acesso aberto
Acesso é fechado Acesso está concedido
Acesso é fechado Somente assinantes

Resumo

Results of experimental determination of the average heat transfer coefficient upon condensation of pure steam αc and steam from air–steam mixture αas.m in tubes of a large-scale model of the emergency cooling heat exchanger in the system of passive heat removal through steam generators of AES-2006 project at Leningrad II NPP are presented. The model contained 16 parallel tubes with a diameter of 16 × 2 mm and a length of 2.9 m connected to the upper steam distributing and lower condensate gathering horizontal collectors; the distance between their axes was 2.28 m. The tube segments were vertical, horizontal, or inclined. The internal diameter of the collectors was 40 or 60 mm. The model was placed in the lower part of a tank with a height of 6.5 m and a volume of 5.85 m3 filled with boiling water at atmospheric pressure. The experimental parameters were as follows: pressure range 0.43–7.77 MPa, condensate Reynolds number Ref = (0.87–9.3) × 103, and average air volume fraction at the segment with air–steam mixture 0.18–0.85. The studies showed that nonuniformity of static pressure distribution along the steam-distributing collector strongly influences the reduction of αc value (ejecting effect). The agreement between experimental and calculated according to statutory guidelines values of αc for vertical tubes is achieved if the dynamic head of the steam flow at the input of the steam-distributing collector does not exceed 1 kPa. Equations for calculation of the diffusion heat transfer coefficient at steam condensation from the air–steam mixture αas.m on the internal tube surface are proposed. In the considered conditions, air is completely displaced by steam flow from the upper to the lower part of the tubes. The boundary between these regions is characterized by an average reduced steam velocity through this cross section of 1.6 ± 0.4 m/s. Above the boundary cross section, it is recommended to calculate αc. according to [1].

Sobre autores

A. Shcheglov

OAO Polzunov Scientific and Development Association on Research and Design of Power Equipment

Email: balunov.ckti@mail.ru
Rússia, St. Petersburg, 191167

V. Lychakov

OAO Polzunov Scientific and Development Association on Research and Design of Power Equipment

Email: balunov.ckti@mail.ru
Rússia, St. Petersburg, 191167

S. Alekseev

OAO ATOMPROEKT Scientific Research and Design Construction Institute of Power Technologies

Email: balunov.ckti@mail.ru
Rússia, St. Petersburg, 197183

V. Kuhtevich

OAO ATOMPROEKT Scientific Research and Design Construction Institute of Power Technologies

Email: balunov.ckti@mail.ru
Rússia, St. Petersburg, 197183

S. Svetlov

OAO ATOMPROEKT Scientific Research and Design Construction Institute of Power Technologies

Email: balunov.ckti@mail.ru
Rússia, St. Petersburg, 197183

V. Sidorov

OAO ATOMPROEKT Scientific Research and Design Construction Institute of Power Technologies

Email: balunov.ckti@mail.ru
Rússia, St. Petersburg, 197183

B. Balunov

OAO Polzunov Scientific and Development Association on Research and Design of Power Equipment

Autor responsável pela correspondência
Email: balunov.ckti@mail.ru
Rússia, St. Petersburg, 191167

V. Il’in

OAO Polzunov Scientific and Development Association on Research and Design of Power Equipment

Email: balunov.ckti@mail.ru
Rússia, St. Petersburg, 191167

Arquivos suplementares

Arquivos suplementares
Ação
1. JATS XML

Declaração de direitos autorais © Pleiades Publishing, Inc., 2017